Datacomm 45-0031-WH Recessed Low Voltage Media Plate with D Manuel d'utilisateur télécharger pdf

Use DataComm Electronics’ Recessed Low Voltage Media Plate with Duplex Receptacle to install low voltage cables behind your flat panel TV, your amplifier

or other audio and video devices. This media plate can be installed upright, sideways.

IMPORTANT INSTRUCTIONS:

This product is designed for retrofit work only because the old workbox cannot be attached to a stud.

WARNING:

Before installing this product, be sure the power is off by switching the circuit breaker to off or removing the fuse(s). Test the power to make sure

the power is off. Be sure to install the Media Plate with Duplex Receptacle in accordance with the National Electrical Code (NEC) and local codes.

Installation Instructions:

Fig. 1 Top view - shows needed space between the drywall and the studs. Receptacle side of the media plate must be 3” from the stud but no more than 5”

(review picture carefully).

Fig. 2 Using the template supplied (see page 2 of instruction sheet), trace the opening needed. Using a drywall knife, cut a hole in the drywall the size of the

template. See Figure 1 before tracing your opening.

Fig. 3 Run the source of power to the included workbox.

Fig. 4 Using the supplied duplex receptacle, connect the hot line (black) wire to the brass colored terminal or screw and the neutral (white) wire to the silver

colored terminal or screw. Be sure to connect the grounding (green) or bare grounding wire to the green colored terminal screw. For shock protection,

this UR, UL recognized component receptacle must be properly grounded. Caution – use copper wire only with this receptacle. Once you have wired

the receptacle, screw the receptacle into the work box until the receptacle is firmly secured.

Fig. 5 Now use the four screws provided to secure the work box to the mounting studs on the backside of the of the media plate.

Fig. 6 Pull all video and audio cords through the recessed opening. Starting with the receptacle side of the media plate, slowing slide the plate into the

opening. Swing the opposite side of the plate into position until the entire media box is flush with the wall. Now screw down the screws with wings;

these wings fasten tightly against the back of the drywall. Switch on the circuit breaker to on or insert the fuse(s). Plug all necessary video and audio

cables. Install your flat panel TV mounting bracket per the flat panel TV bracket manufacturer’s instructions.

WARNING

 DataComm Electronics’ products shall be installed and used only as indicated in DataComm Electronics’ product instruction sheets.

 Instruction sheets are available online at www.datacommelectronics.com.

CAUTION

 For shock protection, this device must be properly grounded.

 Use copper wire only with this device.

DataComm Electronics, Inc.

6349 Peachtree Street

Norcross, GA 30071-1725

888.223.7977

770.662.8205

www.datacommelectronics.com

Instruction / Installation Sheet

DataComm Electronics 45-0031-WH Recessed Low Voltage Media Plate with Duplex Receptacle

Parts Included:

1. 45-0031-WH Recessed Low Voltage Media Plate

2. Old Work Electrical Box

3. 15 Amp/125 Volt Tamper Resistant

Duplex Receptacle

4. Four (4) Screws

Tools Needed:

1. Drywall Saw

2. 6 Ft. Tape Measure

3. Pencil

4. Screwdriver

Fig. 3

Fig. 1

Fig. 4 Fig. 5 Fig. 6

12/21/10 Rev. 2

Page 1 of 2

Fig. 2

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1

Use DataComm Electronics’ Recessed Low Voltage Media Plate with Duplex Receptacle to install low voltage cables behind your flat pane

Page 2 - TEMPLATE

7-1/4” Installation / Instruction Sheet 45-0031-WH (Continued) IMPORTANT INSTRUCTIONS  Read and understand all instructions.  Follow all

Page 3 - Page 1 of 3

Use DataComm Electronics’ Recessed Low Voltage Media Plate with Duplex Surge Suppressor to install low voltage cables behind your fla

Page 4 - Module

Installation / Instruction Sheet 45-0041-WH (Continued) Remember in the event your surge unit alarm sounds, simply remove the replaceab

Page 5

7-1/4” Installation / Instruction Sheet 45-0041-WH (Continued) This product is patent pr

Page 6 - Part # 45-0032-WH

IMPORTANT INSTRUCTIONS:This product is designed for retrofit work only because the electrical outlet box cannot be attached to a stud. WARNING: Befo

Page 7 - Installation Instructions:

Fig. 1 Fig. 2Instruction / Installation SheetRecessed Low Voltage Media Plate with 20 Amp Duplex ReceptaclePart # 45-0032-WH CONTINUEDInstallation I

Page 8

ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT This product is patent protected by U.S. Patent numbers D553475, D554475 and 7390964. RoHS Com

Commentaires sur ces manuels

Pas de commentaire

Datacomm 45-0031-WH Recessed Low Voltage Media Plate with D Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Systèmes de cinéma à domicile Datacomm 45-0031-WH Recessed Low Voltage Media Plate with D. DataComm 45-0031-WH Recessed Low Voltage Media Plate with Duplex Receptacle User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de cinéma à domicile Datacomm 45-0031-WH Recessed Low Voltage Media Plate with D